FAQs

CTI's systems are harder than concrete. Most concrete has a compressive strength of 2000-2500 psi rating.CTI's system has a 7000 psi rating.

‍

Usually, normal washing with a hose is all that is needed. For stubborn stains, a brush with laundry detergent is all that is needed.

The price depends on a number of factors, such as the product line chosen, the condition of the original concrete, the patterns chosen, sealers used etc. However, CTi Dealers can normally find a solution for most any budget.

The cost of the CTI system is normally 20%-25% less than the cost of removing cement and pouring new and is much better looking and much easier to maintain than the original cement.

‍

Yes, quite easily.

Concrete Technology's products have been in use since 1992.

‍

No, CTI's systems are feathered very thin at the joint edge so the coping and decking will be level.

We do apply CTI's systems to cantilever faces and coping stones. Though application over coping stones is a matter of personal preference, it is often advisable to coat the stones unless they are exceptionally new. If not coated, they tend to look old and dirty after the CTI installation is complete. In addition, the older copings which have deep lips can be filled in so the coping stones are level with the deck giving a modern cantilevered look.

Yes, however, multiple spray coats are needed to reduce rebound, or waste.

‍

Yes, CTI's systems can be applied to concrete steps including risers and treads.

‍

Yes, though it generally will need to be scarrified or sandblasted to remove the paint enough to where our product will bond with the original concrete.

The material is repairable to its original state. We service all decks past warranty.

‍

Though we do everything possible to treat cracks and do eliminate 90% of them, it is possible they may reoccur. If they do, it is usually in the form of a hairline, which is not objectionable as it is largely hidden in the texture. However, if a crack becomes too objectionable, it is easy to repair. Proper placement of tension cuts greatly reduces the chance of the crack returning. Check cracking is a natural phenomenon which occurs in rock, dried-out mud flats, paint, and concrete and in ceramic coatings. Cracks in the concrete may be structural or surface cracks. Surface cracks are generally less than a few millimeters wide and deep. These are often called hairline or check cracks and may consist of single, thin cracks, or cracks in a craze/map-like pattern. A small number of surface or shrinkage cracks is common and does not usually cause any problems. Surface cracks can be caused by freezing and thawing, poor construction practices, and alkali-aggregate reactivity. Alkali-aggregate reactivity occurs when the aggregate reacts with the cement causing crazing or check cracks. Structural cracks in the concrete are usually larger than .1/8 inch in width. They extend deeper into the concrete and may extend all the way through a wall, slab, or another structural member. Structural cracks are often caused by settlement of the fill material supporting the concrete structure, or by loss of the fill support due to erosion. The structural cracks may worsen in severity due to the forces of weathering.

‍

Cracks are addressed using our revolutionary "Smart Prep" System.  The Smart Prep system offers a flexible bridge over the cracked area that allows the original concrete to move while not allowing any normal cracking to transmit through the CTi coating.

We can generally improve drainage; however, the degree of success is contingent upon the pitch of the concrete adjacent to the low spot. The low spot will have to be looked at personally by an authorized CTI dealer to let you know what you can expect.

No, not dramatically, the CTI product has approximately a 2% fade factor over seven years, which is undetectable by the human eye; our warranty covers this.

‍

No, the sealer we apply to our system is not affected by most chemicals.

No. Kool Deck® is a product that must be applied to freshly poured concrete within 5 hours in order to bond. CTI's systems can be applied to new or old concrete. In addition, CTI's systems are a three-coat system and are sealed with a finish coat, which makes it impervious to staining. Whereas Kool Deck® is a very porous, non-flexible product, that has a minimal life expectancy.

‍

Here is how CTI's systems compare to other coatings as far as heat retention:

‍

Up to 40 degrees cooler than concrete.

30%-40% cooler than epoxy stone50% cooler than vinyl or urethane

40%-50% cooler than wood decksUp to 40% cooler than carpet

50%-60% cooler than terrazzo

40%-50% cooler than tile

20%-30% cooler than brick

‍

Colors of the product and texture chosen will effect the overall temperature of the surface.

All existing control joints should remain in the surface to allow for expansion and contraction of the original concrete. They are not coated with the CTI system and are masked off. We can, however, work to insure these joints match the rest of the look of the surfaces.

‍

No, the pool should be full. If the pool were empty, the CTI system overspray would stain the plaster. Full, any small amount of overspray can be dealt with by allowing the overspray to settle to the bottom, shutting off the filter, then pumping the material to waste and bypassing all filters is recommended.

‍

An average job will take 1 to 2 days. Larger, more complex jobs may take longer. Clean foot traffic is usually allowed within the same day.

‍

We have a variety of standard colors to choose from. However, we can custom produce any color you wish for a minimal extra charge.

‍

CTI's systems achieve a look, texture and color of any type stone or look you require. A base coat is applied that fixes any imperfections in the original concrete. A design is then laid over it and a hopper gun shoots on a textured layer over that. A final clear coat is put over the system that is nonporous and protects it as well as makes it very easy to maintain. Mold, mildew, motor oil, etc. can be sprayed off with a regular garden hose. Common detergents can be used to remove tough or repetitive latencies.



We generally apply our systems on old concrete between 3/32" to 1/8". CTI's systems are thin layered cements which depend on adhesion through the use of modified acrylics.

‍

Concrete Technology Inc. offers a full line of concrete beautification and restoration products for both residential and commercial use.  CTi has different products that can be used over concrete floors, existing countertops, and even walls.  In the commercial setting, Concrete Technology manufactures a line of tough, durable epoxy and urethane floor coatings that can protect concrete even in the harshest of environments.

CTI offers a 10-year limited material warranty on its Hallmark System against, dramatic fading, delamination, and general product failure.

‍

CTI's main product line called the "Hallmark System", is a color integrated, modified acrylic cement product made of Portland cement, silica sand and a modified acrylic resin for its bonding agent.  In addition, CTi offers product lines that are ideal for restoring, protecting and beautifying laminate countertops, garage and workshop floors, even vertical walls.

‍